Brief Introduction

IV3-G120

ModelIV3-G120ToolsAvailable modesStandard mode / Sorting modeTool with standard modeLearning, Outline, Color area *1, Area *2, Edge pixels, Color average *1, Brightness average *2, Width, Diameter, Edge presence, Pitch, OCR,Color prohibit *1, Brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge), Blob countNumber of toolsTotal: 65 tools *3Switch settings (programs)128 programs (when using SD card) / 32 programs (when not using SD card)Image historyNumber of storable images100 images *4Save conditionsSelectable between NG only, NG and OK near threshold *5, and All *4Image data transferTransfer destinationSelectable between SD card, FTP server, and SFTP serverTransfer formatSelectable between bmp, jpeg, iv3p, and txt, and file names can be modifiedTransfer conditionsSelectable between NG only, NG and OK near threshold *5, and AllAnalysis informationRUN displayTools list (Judgment results, degree of similarity, or degree of similarity bar display) *6RUN informationSwitchable between OFF, histogram, processing time, count, and output monitorHistogram: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGsProcessing time: Processing time (latest, Max., Min., Ave.)Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errorsOutput monitor: ON/OFF status by output *6Other functionsImage capture functionDigital zoom (2×, 4×), HDR, High gain, Color filter *1, White balance *1, Brightness correction, AI captureTool functionsAdditional learning, Mask outline, Masking function, Color extraction/exclusion *1Color histogram function *1, Monochrome histogram function *2, Scaling functionUtilitiesFailing sensor list, Failure hold, Test run, I/O monitor, Security settings (Two-factor password), Simulator *7,Additional FTP/SFTP Image Information, Multi-position adjustment, Multi-master image registration, High-speed program switching, Auto program switching, Auto setting backup/restore, Threshold changing in RUNIndicatorsPWR/ERR, OUT, TRIG, STATUS, LINK/ACT, SDInputTypeSwitchable between non-voltage input and voltage inputFor no-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit)For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.15 mA or lower, ON current 2 mA (for 24 V)Number of inputs8 (IN1 to IN8)FunctionIN1: External trigger, IN2 to IN8: Enable by assigning optional functionsAssignable functions: Program switching, Clear error, External master image registration, SD card save cancelOutputTypePhoto MOS relay output, N.O./N.C. SwitchableMaximum rating 26.4 V 50 mA, residual voltage 1.5 V or less *8Number of outputs8 (OUT1 to OUT8)FunctionEnable by assigning the optional functionsAssignable functions: Total judgment (OK/NG), Run, Busy, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card error, Variety discrimination result, Master judgment resultEthernetStandard1000BASE-T/100BASE-TXConnectorRJ-45 8pin connectorNetwork functionFTP client, SFTP clientInterface compatibilityBuilt-in EthernetEtherNet/IP®, PROFINET *9, TCP/IP non-procedure communicationCommunication unitEtherCAT®, CC-Link, DeviceNet®, RS-232C, PROFIBUS *10Expanded memorySD card (SD/SDHC) *11RatingsPower voltage24 VDC ±10% (including ripple)Current consumption2.2 A or less (including a communication unit, without the AI Lighting unit, and including the output load)3.4 A or less (including a communication unit, with the AI Lighting unit, and including the output load)Environmental resistanceAmbient temperature0 to +50°C 32 to 122°F (No freezing) *12Relative humidity35 to 85%RH (No condensation)MaterialMain unit case: PCI/O terminal block: PAEthernet connector: Copper alloy + Ni platingMain unit rear DIN rail fixing tab: POMPower connector: PA/POMSensor head connector: Zinc + Ni plating/PAMain unit rear heat sink: AluminumNameplate: PCWeightApprox. 300 g 10.59 oz*1 Color type only.*2 Monochrome type only.*3 Tools can be installed by programs. This is the number of detection tools and position adjustment tools. Up to 64 detection tools can be set. The number of detection tools in Sorting mode are eight tools.*4 Saves to the sensor amplifier’s internal memory. The images saved to the sensor amplifier can be backed up to a USB memory stick inserted into the control panel (IV3-CP50) or to the PC where the software for the IV3 Series (IV3-H1) is being used.*5 Learning tool only.*6 Can also be displayed on the control panel (IV3-CP50) or the software for the IV3 Series (IV3-H1).*7 Usable on the software for the IV3 Series (IV3-H1).*8 Make sure to keep a total of each output with 160 mA or less.*9 Conformance Class B, Applicable protocol: LLDP, SNMP.*10 When a communication unit (DL Series) is connected.*11 Use only products recommended by KEYENCE.*12 For situations where the operating ambient temperature will exceed 40°C 104°F, follow KEYENCE’s specified heat dissipation measures to ensure the case temperature does not exceed the rated maximum temperature (65°C 149°F). Check the instruction manual for more information.